TDP Infrared Mineral Heat Lamp Set *KS-9800 * With wheel stand *Floor Model* (Replaceable/Detachable Head)

More Views

TDP Infrared Mineral Heat Lamp Set KS-9800 With wheel stand Floor Model (Replaceable/Detachable Head)

Be the first to review this product

$169.99

Availability: In stock

Short Description

Technical Specification of TDP Lamp

Hz (Hertz) 50 Hz
Spectrum Range 2-25 um
Power 110 V, 220 watts, 3 AMP
Lifting Scope of Arm > 11” (30 cm)
Elevation Degree > 90
Azimuth Degree 360
Life of Mineral Plate 1000 – 1500 Hours
Shining Distance > 8” (20cm)
Adjustable Height 33” – 66”
Oversized Mineral Plate 6.5” Dia. (Reg. size Plate 5” Dia.)

Weight & Dimensions

1 PC: 24 lbs(21 x 17 x 8"H)

2 PCS: 48 lbs(22 x 18 x 15.5"H)

6 Months Limited Warranty on Control Panel and Labor
3 Months Limited Warranty on accessory parts

Due to an increase in tariff imposed by the US government, our importing costs have increased significantly this year. Although we have made every effort to absorb these escalating costs internally, we were left with no rational alternative but to increase our price for this item. We appreciate your business and we hope you understand the necessity for this price increase.

Having Trouble with Assembly here are some videos to help.

Video 1 - How to assemble the full TDP lamp start to finish :

https://youtu.be/aD5tFkOkD8I

Video 2 - How to assemble the TDP head to the TDP lamp easily and less than 2 mins.

https://youtu.be/hD85RI1eo_I

**Free shipping may not be reflected at the time of checkout, but the invoice will be adjusted on our end before the order is charged to your credit card**

Qty:

Description

Details

TDP Lamp - Standing Model

Features of this TDP Lamp:
0 - 60 Minute timer
On/off Switch
1 User’s Guide
2 Extra fuses included

Technical Specification of TDP Lamp

Hz (Hertz) 50 Hz
Spectrum Range 2-25 um
Power 110 V, 220 watts
Lifting Scope of Arm > 11” (30 cm)
Elevation Degree > 90
Azimuth Degree 360
Life of Mineral Plate 1000 – 1500 Hours
Shining Distance > 8” (20cm)
Adjustable Height 33” – 66”
Oversized Mineral Plate 6.5” Dia. (Reg. size Plate 5” Dia.)

*IMPORTANT: Please make sure to wear light clothing when using. DO NOT USE ON BARE SKIN.

TDP ASSEMBLY INSTRUCTIONS

Please see link below on how to assemble TDP Lamp:

https://www.youtube.com/watch?v=aD5tFkOkD8I

TDP Heat Lamp Basic Guideline

1) Please note that the heat lamp will take approximately 10 minutes to warm up. After preheating for 10 minutes, please allow an additional 10 minutes for the temperature to increase.

2) As a general guideline, the distance between the treatment surface and the heating head should be approximately 8-10 inches. Positioning the heating head closer than 8" to the body is not recommended, as burns or damages to the skin may occur. Actual positioning of the TDP head may be adjusted to reach the desired level of heat.

3) A minimum of 40 minutes per treatment session on the targeted area is recommended. Please note that the treatment time for a given session may vary depending on the condition being treated.

4) For treatment purposes, the heat lamp only provides enough heat for therapeutic heat treatments. Please do not expect a higher temperature range, as higher temperatures may cause the skin to overheat and burn.

If the TDP does not heat up, follow the steps below.

1. Turn on the power and check if the orange indicator light turns on. If it does not turn on, replace the two fuses.

To replace the fuses: Open the two fuse cases on the back of the control panel using a Phillips-head screwdriver and replace the fuses in the fuse cases.

2. If the orange indicator light is on and there is no heat, the heating coil located inside the TDP head is broken or has reached the end of its life, so replace the heating coil or replace the head itself.

Replacing the head is very easy, but replacing the heating coil is more time-consuming, as shown in the instructions(1~11) listed above.